Instructions easy to sort out even though only in Japanese. Some installation advice: 1) I placed the large rubber washers between the bracket and the plastic guard itself. 2) Honda NC mirror stalks are hard to understand! The simplest method is to completely remove the mirror by undoing the top nut and spinning off the mirror - this is LEFT HAND THREAD - so turn your 14mm open-end spanner as if tightening a normal nut. Once the is mirror safely on the bench unbolt the remaining right hand thread bolt from the bar with a ring spanner. Fit the bracket and replace the RHT bolt; tighten. Fit mirror with LHT bolt; tighten while adjusting for view. Much easier this way!Item is good quality (although I might have expected the mounts to be of lighter material eg. aluminium, titanium) and they fit well. Seem to do adequate job of protecting my hands and the looks fit the sporty 700S model well (better than big black buckets).I think I made a good purchase.
View Detail
- Verkoop
95.08 ~ EUR (16,401 JPY) 99.72 EUR Save 5%
levering Informatie
-
Please select product form first.
Product detail
Schild dikte : 3mm
Schildlichaam : polycarbonaat
[SIZE]
LENGTH : 150mm
WIDTH : 250mm
DEPTH : 80mm
Roestvrij stalen schroeven
Polycarbonaat Wasmachines
Borgmoer aangenomen
**Niet beschikbaar voor voertuigen met DCT-specificatie.
*De kleur van de montagelijst is "Zwart (poedercoating)".
*Er is geen ruimte of gat voor het installeren van accessoires zoals ETC op de installatiesteun..
* Het beeld is alleen ter referentie. De getoonde afbeelding kan afwijken van de werkelijkheid.
De knokkelbescherming beschermt de knokkels en vingertoppen van de ruiter tegen de rijwind..
De behuizing van het schild is gemaakt van polycarbonaat, en de kleur kan worden gekozen uit helder en rook..
De verstaging is zo ontworpen dat hij sterk genoeg is om rammelen te voorkomen, zelfs als hij aan hoge winddruk wordt blootgesteld, en is ontworpen om aan de linker- en rechterspiegels te worden vastgeschroefd..
Voorzichtigheid
* If there may be an instruction manual included, it will be written in Japanese.
NEW ARRIVALS IN USED PARTS FOR
NEW ARRIVALS IN USED PARTS FOR
NEW ARRIVALS IN USED PARTS FOR
New arrivals in used
New arrivals in used
klanten-reviews
Reviews with image
Fits:HONDA NC700S 12-, HONDA NC750S 12-
Fits:HONDA NC700S 12-, HONDA NC750S 12-
Nov 7, 2012
It was considered how it would be coped with in first winter.Attachment removed and sandwiched the Mirror, and it has equipped with it easily as it attached again.The Brake side also only turned the Throttle wire under some.A Style is also pleasing and it is likely to meet the expectation of the measure against cold.
View Detail
Fits:YAMAHA SR400 10-21
May 27, 2022
I bought it for winter protection in the Kanto area and never froze when used with winter Gloves, which are not that thick.
Installation is also easy, as long as the RightMirror is co-tightened with the Mirror and the RightMirror has an Opposite Thread Screw.
The Bracket is solid and the Screen is strong enough to touch.
As is the fate of the SR400, the engine vibration is fine but shaky.
Fits:SUZUKI GSX1400 01-08
Jan 10, 2021
I bought it because I could not stand the strongest cold wave. When I put it on, it didn't look as bad as I thought it would, and I was more than satisfied with the Large effect. The cold wind hitting the fist is reduced, and I think that this is Large sturdy even without Grip heater. It is easy to install and remove, so I recommend it to riders who ride in the middle of winter.
View Detail
Fits:SUZUKI
Aug 11, 2020
It is a necessity in the middle of winter, but it cannot be surpassed by this alone. After that, Grip heater installation. Still cold, Komine electric heat Gloves device. It's still cold. It looks like the image of the armor. But I can't repair the damage if I stumble on it. If you buy the AcrylicGuard part cheaply, you may be able to fit it to any type of armor. However, in winter, in order to change into Long Screen of SEA BASSOEM Product, if you cut all the Handlebar as much as possible, it will hit Screen. You may need longer bolts to remove the Handlebar and fit it back in. Also, please make sure to periodically retighten the Acrylic and Handlebar parts to prevent them from coming loose.
View DetailNew Custom Articles
