frameschuifregelaar

Fits:KAWASAKI ZZR1200 02-

Japanese Webike user

Excellent

Oct 27, 2021

Pretty secure Guard.

The ZZr1200 is OEM and CowlParts will not be available, so I bought it as a fallback.
It's pricey, but it's very sturdy and solid, and if it's just a standing joke, you can rest assured that Cowl will be well protected.
If you ride ZZr1200, I think that it is the parts that there is absolutely no loss if you have bought it in the point that you can also buy a sense of security.

Personally, I was happy with the fact that I could install it without having to remove the Cowl.
However, it may be a little difficult because the Bolt on the body side is very hard.

Helpful?

To protect out-of-print exterior ...

Fits:KAWASAKI ZZR1200 02-

Japan User(translated)

Very Good

Mar 3, 2017

Although it was also used in ZZr 1100, Side cowl heard that Manufacturer stock wipe out, and it hurried up.

1100 decomposed the Side cowl, but in the case of 1200, since Bolt to remove is full,
You can install it as it is. (About 10 minutes per one in One Side. )

Although it is in Parts that I do not want to be active so much, but the degree of peace of mind is different if attached.

Helpful?

Not too obvious, but firmly guarded.

Fits:KAWASAKI ZZR1100 D 93-01

Japanese Webike user

Very Good

Dec 11, 2020

It was installed to protect the Blinker from damage and the Cowl in the event of a fall.
High quality and excellent design.

Installation was easy with the Instruction Manual.

In terms of price, it seems a bit pricey.

I still don't know the strength and effectiveness of it, but I'd prefer not to have the opportunity to try it.

I think of it as insurance in case of a fall.

Helpful?

Fits:HONDA CBR 125 JC50 11

Japan User(translated)

Average

May 14, 2020

It was not Bolt On

The position of the Bolt hole of one of the resin parts does not fit, and it is necessary to correct the hole using the stick file by oneself and to make a new hole The cost may be high, but after a provisional assembly inspection, I was able to assemble it It would be more conscientious to be shipped In addition, because the Base is aluminum and the screw hole is cut shallow, I feel that it is weak in terms of strength I made it lightly to tighten

Helpful?

No-machine installation available!

Fits:KAWASAKI ZZR1100 D 93-01

Japan User(translated)

Very Good

Apr 23, 2020

Other people have already implied how to install it and so on
Describe the Texture and Material!

The base of the Slider is aluminum cut-out, and the cutting marks are beautiful! It is hard to see in the photo, but it is not anodized in the aluminum base material Mm!
Which means you'll have to polish it from time to time if it's going to keep the shine it had when you bought it!
Although it is aluminum, the white rust definitely makes it cloudy

Also, the base of the Slider is tightened with Frame and Bolt, and the UnderTube is clamped with Clamps Fixed
This Clamp is iron, probably due to strength issues!
I'm sure Rust will progress here for sure!
It is not visible from the front, so before you install it, you need to take a look at the Chassis [Color] I think Clear or very thinly Grease up will help prevent Rust!
I had to deduct points for texture for these reasons
The price is not cheap, but it's an insurance policy because the Wound will be in the Cowl even if you're a standing mockery Recommends a purchase

Cowl is discontinued, and the paint job is a color clear finish over base color I think it will cost Gold!

The installation rate of this car is so high that it can be said that it is always installed in a certain famous ZZR system shop's So I'm sure it's the right product!