26.75 EUR
(4,380 JPY)
25.06 EUR
(4,102 JPY)
(6% OFF)
5 (2 alle Reviews)
Very Good
Non-disassembled exhaust system assembly etcIt is used to assemble Silencer to a non-disassembled exhaust system
When the Glass Wool used in Silencer wears out and needs to be refilled, or when the Glass Wool used in the Silencer is not used, it can be refilled inside When doing the Small work, Silencer must be disassembled (photo1)
Some manufacturers will refill Glass Wool for you! But with this, you can replace it yourself
When removing the Rivet, the original Rivet head is rubbed off with the Drill (Photo 2)
When performing a rivet, you can add a Blind rivet to the Riveter with Quantity:Set the Handlebar on the hole to be riveted and grip the Handlebar If you can't hold it once, open the Handlebar again and grip it again The Drumstickon and unwanted pins are cut off
That's it
There are four different sizes of Nose peace for different sizes of Rivets For working in a secluded area, there is a long nose peace and It's also kind of nice that Spanner is included Photo (3)
Depending on the material to be riveted, the material of the Rivet itself may also be Steel or You can choose from Stainless Steel or other materials, but Stainless Steel is harder, so it is a bit more expensive Note that the available diameter will be smaller (Photo 4)
When working on multiple locations, you can insert the Rivet into the holes beforehand so that the holes can be gapped and the Rivet can be removed There is no such thing as being unable to insert
There is a little hang, but you will not fail if you get used to it
It's well made and not likely to break so easily
Nut and the place where Bolt.Nut cannot be used by any means, and the Sunday Large construction etc. of Others I think that the frequency of use is low because it can be used, or it is convenient when there is
Reviews For SK11 popnagelmachine From Other Webike User
Excellent
Well made.Purchased to disassemble and clean Exhaust System.
The product is solid and durable.
The size of the Rivet can also be covered with the size that would normally be used.
Size can be changed by replacing Adapter.
Crimping the Rivet takes a lot of force.
Crimp firmly without fear of injury.
It's not a tool you'll use over and over again, but it's the kind of tool you can find at a hardware store.
Unlike cheaper products, this product is well made, so if you look at it in the long run, you will find that this product is better than the cheaper ones.
I think it's goodView Detail
Most Viewed Reviews Of SK11 Rivet Tools
Excellent
Well made.Purchased to disassemble and clean Exhaust System.
The product is solid and durable.
The size of the Rivet can also be covered with the size that would normally be used.
Size can be changed by replacing Adapter.
Crimping the Rivet takes a lot of force.
Crimp firmly without fear of injury.
It's not a tool you'll use over and over again, but it's the kind of tool you can find at a hardware store.
Unlike cheaper products, this product is well made, so if you look at it in the long run, you will find that this product is better than the cheaper ones.
I think it's goodView Detail
Excellent
Convenient to haveI bought this to install fogs on my Motorcycle.
Pipe is drilled and the nut is crimped with a nutter here.
Easily install fog or anything else with Bolt tightening.
I do need to drill some holes with a Drill.
Once processed with a nutter, the parts can be installed and removed with Bolt On.
There is a difference in finish between with and without.
It's a solid product, and it's a good product.
The work was not difficult or broken down.
I think it's a good productView Detail
Average
Used for Silencer's RivetI used it to replace Silencer's Wool.
It is used for the Rivet at the Silencer end. The material of the shaft part is Steel because the material of the shaft part is more stressfully struggled when struggling with the Drill later.View Detail
Excellent
To the thickness that cannot be tapped, etcI often use a nutter for something so thick that the Tap can't cut it
Thin plates can be fixed with a bolt nut, but you can also set up a bracket on a frame or other parts The best place to do this is usually with a co-tightening on the Bolt somewhere, but it's not the best place Sometimes you really want a Screw hole
If you have one, it's a necessity because it's useful for anything and we often do diversionary parts
But even with M5, you can drill a pre-drilled hole of about Φ7, so consider the strength of the hole, depending on the location And if the hole you drilled is Steel, it's best to paint it to prevent rustView Detail
Other Reviews From Japan User(translated)
Excellent
Radipon handled in Mild?attachment
The CBR650R is mounted at the same position angle as the NORMAL.
However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away.
I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose.
・NORMAL (Reserve integrated horizontal master) Impressions of
No complaints on public roads. Familiar feel and very easy to handle.
However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful.
Radipon (Reserve separate body portrait master) Impressions of
It was totally different from what I expected, my expectation was that it would feel like a Rear brake…
It is really a mild and easy-to-handle radipon.
On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN?
But I felt the radipon effect from Breaking a little stronger, and
It can be hung up to a hard brake without effort.
I felt trust that this could stop.View Detail
Very Good
packtalk bold Attached MountI purchased this for use with multiple Helmets. 。
Mount included with the BOLD.
Microphone and speaker are not included and must be purchased separately.View Detail
Excellent
Grip replacementGrip that had been used for a long time was worn out and had to be replaced.
They are soft and dampen vibration.View Detail
Very Good
Works well in everyday life[How is it used?
Used to lick Screw loose.
Was the one you received as per Image?
As per Image.
How was your experience with it?
When used on a strongly tightened Screw, it can be safely and securely removed.
The licked Screw was removed.
It is also useful for DIY Screw removal.
[Points to note]
When used on a licked Screw, it is best to beat it in with a Hammer before use.View Detail
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING