[geluidsdemperspecificaties]
Dikte : Φ90
Geluiddempermateriaal : aluminium (Al)
[uitlaatpijp specificaties]
・Assembly methode : 4in1
Buitendiameter van de staartpijp : Φ60.5
Diameter uitlaatpijp : Φ42.7
Uitlaatpijpmateriaal : titanium (Ti)
[set bevat].
・Assembly deel
Kiesbuis
8 bronnen
Geluiddemper
Eindschot
Geluiddempingsband
Geluiddemper Verblijf
Uitlaatpijp voor 1 auto
[onderhoudsgegevens]
Afvoerbout : Montagedeel moet worden losgemaakt
Vervanging van het oliefilter : Montagedeel moet worden losgemaakt
Middenstand : X
*De eindschotten zijn al op het moment van verzending op de geluiddemper gemonteerd.
*Conische titanium geluiddempers V-1/V-2/V-3 worden niet geleverd met een geluiddemperband, omdat er al een versterker is geïnstalleerd.
De geluiddempers van de NITRORACING-geluiddemper mogen nooit worden verwijderd. Het is ook aan te raden om de geluiddemper regelmatig te controleren en te reviseren.
Het is noodzakelijk om over te stappen op een enkele stap terug. In zo'n geval, als u wisselt van voorraad naar dit product, moet u het frame van het tandemstappendelen doorsnijden.
Afhankelijk van het type knipperlicht kan het nodig zijn om het knipperlicht te vervangen.
Het filterdeksel en de aftapbout moeten worden vervangen door een vlak type. De Flat Cover & Drain KIT is inbegrepen in de EX Muffler KIT en moet worden vervangen wanneer de uitlaatdemper is geïnstalleerd.
Compatibel met NITRO RACING Tandem Step KIT Type2. (In zeldzame gevallen waar de NITRO RACING Tandem Step KIT type 1 al is geïnstalleerd, kan er interferentie zijn tussen het bovenste deel van de geluiddemper en de Tandem Step KIT als gevolg van de positie van de montageplaat).
Geluiddempersteun is niet compatibel met de standaard achterwielophanging.
[Silencer Specification]
・Thickness: Φ90
・Silencer material: Aluminum
[exhaust pipe specs]
・Assembly method: 4in1
・Tail pipe outer diameter: Φ60.5
・Exhaust pipe diameter: Φ42.7
・Exhaust Pipe Material: Titanium
[Components]
・Assembly part
・Tail pipe
・8 springs
・Silencer
・End baffle
・Silencer band
・Silencer Bracket
・Exhaust pipe per vehicle
[Maintenance Data]
・Drain bolt: Manifold section needs to be detached
・Change oil filter: Manifold section needs to be detached
・Center stand: Not available
*The end baffle is pre-installed on the silencer at the time of shipment.
*Conical titanium silencers V-1 / V-2 / V-3 do not come with a silencer band as a bracket is pre-installed.
Never remove the exhaust baffle from the NITRO RACING silencer.It is also recommended to check and overhaul the silencer's internal sound deadening wool on a regular basis.
It is necessary to change to a single type rearset.In this case, it is necessary to cut off the frame of the pillion step when you replace the stock one with this product.
Depending on the type of blinker, it may be necessary to replace the blinker.
It is necessary to change the filter cover and drain bolt to a flat type.The Flat Cover & Drain KIT is included in the Exhaust Kit and should be replaced when the exhaust is installed.
It is compatible with NITRO RACING Pillion Step KIT Type2.(As to the vehicles already equipped with NITRO RACING Pillion Step KIT Type 1, there is a rare case of interference between the upper part of the silencer and the Pillion Step KIT due to the welding position of the mounting plate.)
The exhaust bracket is not compatible with the stock rear suspension mount.Compatible with laydown mount adaptation with M6 screw hole construction.
* Please note in advance that cancellation and/or return of this product cannot be accepted once the order has been placed.