Very Good
Almost no problem if OEMExhaust System installation position ? ? ? Wonder.Replacing the Exhaust System is common in enjoying Motorcycle, the problem is how to install that Exhaust System,
Usually I think that the Muffler maker is designed so that it can be attached using the OEM mounting hole, but individual differences in Motorcycle
There are times when the position of the hole is slightly deviated when falling etc., so there are many things that are structured to be somewhat Adjustable,
However, using Bracket and Bracket like the one we have taken for fine adjustment, Washer and color etc.
You have to adjust the position, you installed to install, but often do not refresh,
Some cool Cool Emblem may even hide in Exhaust Band,
Also, I think many people exchange OEM footpeg for Rear Sets etc, but at that time the mounting hole of Exhaust System itself
Often it is lost, in such a case traditional Bracket and Bolt nut ? Needle Gold ? Tape and others,
It was necessary to devise such as diverting parts of other vehicle types, but recently the Aftermarket parts manufacturers side also responded,
Many places that prepared correspondence properly, this NITRO RACING is also one of such a kind Manufacturer.
Well, how about the quality of this product personally, NITRO RACING is a Manufacturer who often uses it, GPZ 900 R
As for the quality part, the Aluminum Cut-out parts have good accuracy, the welding is good ? Including paint
The finish is also very beautiful, I think that Sense of Design is also good, but Design is Large by personal preference Quantity : Pair (for Left and Right) Therefore,
Let me say that there are a lot of my favorite products, but for this product a little finish is rough, cut the aluminum board and then
Did you put the angle at PRESS? I do not know the certain thing, but the aluminum cut-out of Rear Sets etc.
There is no splendid product, it would be inevitable if you think about the price of about 12000 yen, if you want to make this with Cut-out
If you do lightly it will do 3-4 thousand yen, considering saying that it is a part of a single vehicle quality ? I think price is obvious.
As for installation, it can be installed almost at the position of the hole of the OEM when assembled according to the Instruction Manual, processing on the car body is not required,
Bolt species also Quantity : Set and it will be possible to combine without difficulty,
attachment ? Although there is no problem in accuracy, it is regrettable that there is no feeling of Firmly somewhat shaky, but if you shake it by hand with the Exhaust System attached
Easily shake, and even when running it is also a small step in Quantity : Pair (for Left and Right) It seems that it is swaying in (I saw it behind me) Fixed with one Bolt
It is natural because it is cantilevered structure, although it is natural, if it is usual use it will be of no problem and it will be a problem with the Exhaust System and Tandem
If I do not try to ride, I do not think it will break ? ? ? , A worried person should improve it by taking a single effort,
However, since it does not work on the car body, the package Hook is spoofed and it does not interfere with Cowl and it is made into a product,
I think it's wonderful..
This time I purchased for installation of YOSHIMURADSCCYCLONE, not OEMExhaust System installation,
Yoshimura cyclone's Silencer mounting hole position, which is not assembled in NORMAL, is a little gapped from the car body,
Also because OEM footpeg is used for a while, as a result the position of the hole will be slightly diagonally upward slightly behind the position said to say,
So we added processing to this NITRO RACING's Exhaust Bracket,
Since the angle of the Bracket has to be changed from the root at the processing obliquely backward slightly above,
Two Bracket dishes Bolt Drilling the hole position just in a good position, I just hit the bending part, so do not tray the dish Cap screw
It was decided to stop drilling with stages for the purpose, because the angle changed and the top of the Bracket protruded, so the extra part was Cut,
Because it was Aluminum it was easy to cut off,
Since it has to be put out a little further than the car body, Bracket bends a bent part of the root a little more,
The bending of the mounting hole of the Exhaust System was adjusted so as to become parallel to it accordingly, this was just the position of a good hole, but as a work procedure
It is better to decide the bending first, then adjust the angle,
And as I wrote earlier, the texture is somewhat lowered, so we treated it with Sandblast and painted it with matte black and finished it.
I think that there are a lot of people to process until this point, but I think that it is also in the price range that can do such processing, as I wrote the first
Because it is 12000 yen it is possible to do not think as a processing base that this is a product of 45000 yen, because it is 12000 yen
I want to thank the Manufacturer who sells at this price because I can challenge without fear of failure,
Also I think that it is a fun place for Motorcycle to be able to enjoy such processing like yourself.View Detail