- Past bij:
- HONDA Super Cub 50 (AA01-100 - 170) Stock compatible part number: 90752-GK4-003
- HONDA Super Cub 50 (C50-020 - 210) Stock compatible part number: 90752-GK4-003
- HONDA Super Cub 70 (C70-100 - 140) Stock compatible part number: 90752-GK4-003
- HONDA Super Cub 90 (HA02-180 - 210) Stock compatible part number: 90752-GK4-003
- HONDA little cub (ALL MODEL) Stock compatible part number: 90752-GK4-003
The Super Cub custom had over 60,000 km on it and at the last tire replacement, the dust seal was coiled, so the bearing was replaced as well.Lees verder - Past bij:
- HONDA
- HONDA
- HONDA
- HONDA
- HONDA
- ...en meer.
I replaced my MONKEY front and rear Axle Shafts with new OEM ones and I bought these to go with them.:There are some parts which are sold cheaply with the set, but I made the front and rear OEMAxle Sh...Lees verder - After 10 years of operation of the maxiscurator, the grease dried up in the drain bearings and they became unusable. A play appeared on the wheel. I replaced them with Koyo bearings. I need to remove ...Lees verder
- Past bij:
- HONDA
- HONDA
- HONDA
- HONDA
- HONDA
- ...en meer.
I bought it to install PMC's Blinker Bracket for MACHI couldn't find this size at home center and it's the cheapest, so I chose this oneNo glitches. It's just a regular good NutLees verder - Past bij:
- HONDA monkey (Z50J-J9)
I was also worn out and exchanged with Axle Shaft. I'm wearing GInker's 8Inch4jWheel at G Swingarm, but in my case this color interfered and did not enter. Sharpened with a lathe.Lees verder - Past bij:
- HONDA
- HONDA
- HONDA
- HONDA
- HONDA
- ...en meer.
[Webike Monitor] Exchange with the original manufacturer's product.
Slack is prevented with U Nut with the Friction ring.
Lees verder - Past bij:
- HONDA
- HONDA
- HONDA
- HONDA
- HONDA
- ...en meer.
It is the structure of preventing slack similarly pure.
Since the slack of the Axle Shaft under run is dramatically dangerous, it considers that it is better to exchange together in the case of tire ...Lees verder - Past bij:
- HONDA MONKEY (Z50JZ-)
Since parts required for exchange had become a Set, it was good.
Lees verder - Past bij:
- HONDA
- HONDA
- HONDA
- HONDA
- HONDA
- ...en meer.
Since it is a nut of locking, there is no fear of loosening by vibration, and it can feel easy and use it.Lees verder - Past bij:
- HONDA
- HONDA
- HONDA
- HONDA
- HONDA
- ...en meer.
Honestly the product here is too cheap. . . The cfc axle and rear axle of the super cub 110, and a pivot shaft (swing arm shaft). The flange nut of M12 (P:1.25) is being used for the above three shaft...Lees verder - Past bij:
- HONDA NSR50 88-92
Since the used wheel was got, bearing exchange was needed and purchased. Although the bearing itself can also purchase others, the parts number of brand-name parts, such as a dust seal, is not known, ...Lees verder - Past bij:
- HONDA MONKEY (Z50JZ-)
Since I was using the Chinese hub, it was able to respond here.Lees verder
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING