- bought this OEM bolt when I needed to do work on my tdub engine.TDUB ,The flywheel is mounted onto the tapered end of the crankshaft. It is secured from rotating with a Woodruff key, and is tightened ...Lees verder
- Great exactly what I need for fjr. It smells like an old item but its well oiled & kept. Parcel came in very well packed too though delivery took some time.Lees verder
- I used to use wood screw for valve adjustment job in the past.This OEM tappet adjuster tool quality seems suitable for light work that it will see in a DIY .The square swivel does fit.I can use this ...Lees verder
- Purchased to remove Locker Arm on xs250sp 4a8.I bought it without checking because it was mentioned in the tool section of the service manual and was also used in the photo of the procedure for removi...Lees verder
- Since it is an OEM, I don't think this is the best way to go about it.I don't know until I need to be concerned about OEMs.Lees verder
- Product well received, package was bubble wrapped delivery was fast. Highly recommended to buy. Tested Multimeter in good working order.Lees verder
- Used for double-sided tape replacement of electrical components, etc.The adhesive strength is good and the quality is fine as it is made by 3M, which is a reliable company.Lees verder
- The performance is very good and easy to use Tape.It is easy to use because it is not sticky even when used in areas that get hot from heat.The price is rather expensive, but it is definitely easier t...Lees verder
- Uses 3M double-sided tape, which has an established reputation.In this temperature, it sticks strongly.Last week, I was using ButylTape.It didn't stick at all, so I tried again with 3M.I wasn't sure i...Lees verder
- I bought it to watch PistonTop.It's great to be able to use it in the car as well as in the motorcycle.Plug holes are used to ensure stable gauge measurement.Lees verder
- YamahaOEMDial gaugeSTANDThe Large variation is useful for viewing the upper dead center of the piston.Until now, I had to extend the Dial gauge and insert it into the Plug hole, but with this STAND, I...Lees verder
- I bought this to remove the locker arm shaft from my SR400, but I didn't need to use the slide hammer. I didn't need to use the slide hammer. I just screwed it in and pulled lightly, and it came out e...Lees verder
- I bought this to remove the locker arm shaft from my SR400, but I didn't need to use the slide hammer. I didn't need to use the slide hammer. I just screwed it in and pulled lightly, and it came out e...Lees verder
- The adhesive strength seems to be strong. I put it on the place where there is a lot of vibration, but it doesn't seem to come off. It's been 2 weeks since I put it on and I've only driven 40km, so I'...Lees verder
- [How is it used?TZr250R (3XV) I used it to remove the Flywheel from the generator inThere are cheaper MagnetPullers made in China, but I chose this product because it is an OEM Product, which is menti...Lees verder
- Bonjour, je suis très satisfaite, du produit, envoi très rapide, très bonne communication, suivi de commande, je vous remercie pour cette prestation, cordialement Mme BROQUET
---------------------...Lees verder - 1KT (TZr250) I used it in the I used the Universal Product one before, but it didn't come off well and the tool lost, so I bought the OEM Product. It was easy to use and came off easily with the OEM t...Lees verder
- It's an OEM tool and I had no problems working with it.Lees verder
- If you compare the price with cheap Vinyl Tape, it is more expensive, but the performance is very easy to use and maintenance is excellent. It is easy to use because it doesn't stick even if you use i...Lees verder
- OEM tool with low price and reliable.There is a similar tool made in C country, but the price is not so different and the reliability is much different, so there is no Merit to challenge.I think it's ...Lees verder
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING